ID-S - Simple Design

ID-S  Simple Design Type - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-S - "Solar" Simple Design

ID-S "Solar" Simple Design Type - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-C - Standard Type

ID-C Standard Type - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-C Absolute Encoder Digimatic Indicators Series 543 - Calculation Type

• A conventional Digimatic indicator simply displays a spindle displacement, but the Calculation-Type Digimatic indicator incorporates an internal calculation function in place of spindle displacement. With fixtures, measurements such as feeler, inside diameter and radius of curvature measurement can easily be obtained without the hassle of conversion tables or equivalents.

• The Absolute Digimatic indicator performs internal calculations using the formula Ax+B+Cx-1 (assuming spindle displacement as x) while the specified coefficients A, B and, C can be set with respect to the purpose of measurement or dimensions of the fixtures. This unique feature allows you to read your measurements directly, without fumbling for conversions.

ID-C - Calculation Type

ID-C - With Green/Red LED - GO/NG Signal

Accuracy

SPC

IP Rating

.00005"/.001mm

.00005"/.001mm

.0005"/.01mm

.0005"/.01mm

• The maximum, minimum, (Peak Hold) or runout value can be displayed during measurement.
• GO/�NG judgment is performed by setting the upper and lower tolerances for max., min. and runout values.
• High speed sampling ratio of 50 times/s.
• Employing the ABSOLUTE linear encoder, the Signal ID-C always displays the spindle "Absolute Position" from the origin at power-on
  The Signal ID-C achieves the IP54 protection level to resist dust and contaminants for safe operation in harsh machine shop environments.

ID-C - With Max/Min (Peak) value Holding

Accuracy

SPC

IP Rating

ID-C - For Bore Gage

ID-C For Bore Gage -  ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-U Absolute Encoder Digimatic Indicator  Series 575 -Slim and Simple Design

• Slim type digital indicator with low price.
• Large LCD and simple key operation.
• After the initial origin setting, the ID-U no longer needs absolute positioning over the entire battery life; the origin is remembered even after power-off.
• Ideal for installation into measuring devices because of it’s compact design and long battery life.
• Employing the ABSOLUTE linear encoder, the ID-U always displays the spindle "Absolute Position" from the origin at power-on. Also unlimited response speed eliminates over-speed errors.
• Flat back type only no option for backs
• SPC data output.

ID-U - Slim and Simple

ID-U Slim and Simple Design - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-F  Absolute Encoder Digimatic Indicators Series 543 - with Back-lit LCD Screen

• With the ABSOLUTE Linear Encoder technology, once the measurement reference point has been preset it will not be lost when the power is turned on.

• GO/�NG judgment is performed by setting the upper and lower tolerances. If a judgment result is out of tolerance, the display backlighting changes from green to red, so tolerance judgment can be made at a glance.

• An analog bar indicator has been integrated to handle upper/lower limit approaching and zero approaching. It enhances the ease of operation in the same manner as a dial indicator. The display range of the analog bar can be changed.

• With SPC data output.

ID-F - Backlit LCD

ID-F with Back-Lit LCD Screen  - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-N/B  Absolute Encoder Digimatic Indicators Series 543 - with Dust/Water Protection to IP66

ID-N- Slim Type  ---  ID-B Back Plunger Type

• Proven ABSOLUTE sensor.

• Rated to IP66 water- and dust-proofing standard and oil resistance improved.

• Slim body design is advantageous for multi-point measurements.

• Improvement in workability with the LCD readout-rotation function.

• Back plunger design (ID-B).

• Built-in tolerance judgment function.

• Switchable resolution.

• Waterproof data output connector.

• Built-in hold/preset function.

ID-N - Slim  - -  ID-B Back Plunger

ID-N Slim Type - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-B Back Plunger Type - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric

ID-H  Absolute Encoder Digimatic Indicators Series 543 - High Accuracy and High Functional Type

• This new-generation digital indicator offers the excellent accuracy and functionality expected from this class of indicator. Take advantage of its high accuracy backed up by 0.5�m / .00002" resolution, remote control functionality via a handheld controller (or an RS-232C interface) and easy runout measurements with the well-established analog bar display.

• The maximum, minimum, or runout value can be displayed during measurement.

• GO/�NG judgment is performed by setting the upper and lower tolerances. If a judgment result is out of tolerance, the display backlighting changes from green to red, so tolerance judgment can be made at a glance.

• With SPC data output.

• With RS-232C input/output.

• Optional Remote Controller

ID-H - High Accuracy and High Functional

ID-H  High Accuracy and High Functional Type - ANSI/AGD Type (3/8" Stem and 4-48UNF Contact Point) - Inch/Metric